If you’ve ever wandered into a precision machining shop, you’ve probably glanced at the racks of scrap metal—copper pipe ends, flattened brass fittings, chunks of bronze flashing—and wondered how different cutting tools handle these soft, workable alloys. As a Sawjet supplier, I get this question constantly: Can our Sawjet system, which combines a high-powered abrasive saw with a focused waterjet stream, actually cut through copper and brass? The short answer is yes, but there’s a lot more nuance to that “yes” than you might think. Today, I want to break down how our Sawjet works with these metals, why it outperforms many other tools for copper and brass, and what that means for your shop if you work with these materials daily. Sawjet (Saw Cut & Jet)

Let’s start by clearing up what a Sawjet actually is, because it’s not just a regular abrasive saw or a standalone waterjet. A Sawjet marries two technologies: a rotating, diamond-tipped saw blade that does the heavy cutting, and a high-pressure waterjet that blasts coolant and small amounts of abrasive material directly at the cut line as the blade moves. The waterjet does two key things here: it cools the metal to prevent overheating, and it flushes away metal chips as the blade cuts, so they don’t jam the blade or leave rough edges. Copper and brass are both relatively soft compared to steel or titanium, but they have unique properties that make them tricky for some tools. I’ve seen shops try to use old-fashioned band saws for copper only to end up with smudged, deformed edges, or regular waterjets that take way too long to cut through a quarter-inch brass plate. That’s where our Sawjet shines.
First, let’s talk about why copper and brass present specific cutting challenges. Copper has high thermal conductivity—meaning it absorbs and transfers heat really well. When you use a tool that generates a lot of friction, like a standard abrasive saw, that heat can build up at the cut site and cause something called “work hardening” in copper. Work hardening is when a metal becomes harder and more brittle as it’s deformed, so the cut edge gets tough, the blade wears out faster, and you might end up with cracks or uneven cuts. Brass, which is an alloy of copper and zinc, has its own quirks: it’s more brittle than pure copper, so it can chip if you apply too much pressure, and it tends to produce fine, sticky chips that can clog saw blades or waterjet nozzles. I’ve had a customer who runs a custom plumbing parts shop tell me they went through three band saw blades a week cutting 1-inch brass bars before they switched to our Sawjet. That’s the kind of real-world pain point that made us refine our Sawjet system specifically for non-ferrous metals like copper and brass.
So, how does the Sawjet solve these problems? Let’s get into the science, but keep it practical. The diamond-tipped blade in our Sawjet is designed with a specific grit size—we use a medium-fine diamond grit for copper and brass, not too coarse that it tears the metal, not too fine that it drags. But the real game-changer is the integrated waterjet stream. As the blade cuts, the waterjet hits the exact point where the blade is making contact with the metal, keeping the temperature at the cut line around 120°F to 150°F. That’s way below the temperature where copper starts to work harden—most standard abrasive saws hit 500°F or higher in the cut zone, even with coolant. For brass, that cooling effect prevents brittleness and stops the fine chips from melting and sticking to the blade teeth. The waterjet also flushes those chips away immediately, so they don’t get ground back into the cut and cause rough edges or blade wear.
I test every Sawjet setup we sell myself, so I’ve cut through everything from 1/8-inch copper wire to 6-inch solid brass bars to ½-inch thick copper plates with our system, and the results are consistent. Let’s compare that to other common cutting tools to put this in perspective. A standard abrasive saw can cut copper, but it leaves a rough edge that needs secondary grinding or sanding, and blade life is short—we see customers go through 10 to 15 blades a month cutting heavy brass parts, whereas with a Sawjet, those same shops go through 2 to 3 blades a month. A standalone waterjet, on the other hand, cuts very clean edges, but it’s slow. Cutting a 4-inch brass plate with a waterjet can take 10 to 15 minutes, whereas our Sawjet cuts that same plate in 90 seconds. That’s a huge difference for shops that need fast turnaround on parts.
Another thing people ask me is about the finish. If you’re cutting copper or brass for parts that need to be polished or plated, the edge quality is non-negotiable. I’ve seen shops use a regular band saw for brass fittings and have to spend 5 minutes per part sanding the edge to remove burrs. With a Sawjet, the edge comes out almost ready for finishing—there’s a tiny, almost unnoticeable burr, maybe 0.005 inches high, that you can wipe off with a rag. For copper, the edge is smooth enough that many customers skip the secondary sanding step entirely, which saves both time and money.
Wait, but is there any limit to what thickness you can cut? We’ve tested up to 8-inch solid copper bars and 10-inch solid brass bars with our standard Sawjet, and the cut was straight and clean the whole way through. For thicker materials, we can adjust the blade speed and waterjet pressure to compensate—for example, slower blade speed for thicker brass, a slightly higher waterjet flow to keep chips flushed. We also have a smaller, benchtop Sawjet for shops that work with smaller parts, like 1/16-inch copper tubing or thin brass sheets, and that works just as well without warping the thin material. Thin copper is especially tricky because it’s soft and can bend or deform under pressure, but the waterjet’s support along the cut line prevents that bending.
I should also mention something about material waste. Copper and brass are expensive metals—most shops pay $3 to $5 per pound for copper, and brass is close behind. When a tool leaves a rough edge, you end up trimming off 1/8 inch or more from each part to get a clean finish, which adds up to a lot of wasted metal over time. With our Sawjet, the kerf (the width of material removed during cutting) is only about 0.06 inches, which is way narrower than the kerf of a band saw or even a standard abrasive saw. That means less material is wasted per part, which adds up to big savings on high-volume orders. One customer who makes electrical connectors told us that since switching to our Sawjet, they’ve reduced copper waste by 12% on 50,000-part runs. That’s thousands of dollars saved every year just on material.
Of course, no tool is perfect, and I’m not going to sugarcoat it. A Sawjet isn’t the cheapest cutting tool out there, especially for small shops that only cut copper and brass occasionally. But if you’re running a shop that does daily production of these materials—plumbing parts, electrical components, decorative metalwork, automotive parts— the ROI (return on investment) is quick. Most of our customers pay off their Sawjet in 18 to 24 months, depending on their volume, because of reduced blade costs, less secondary finishing, and less material waste. We also offer training and ongoing support, so you don’t have to worry about figuring out how to use it on your own.
I’ve had a lot of skeptics over the years, too—shops that have used other waterjets or saws and think they can’t be beaten. Last year, I visited a custom metal fabrication shop that specialized in brass door hardware for high-end homes. They were using a 10-year-old abrasive saw that was leaving rough edges, and they were losing bids on jobs because their delivery times were too slow compared to competitors with waterjets. They tested our Sawjet on a 2-inch solid brass bar, and when they saw the cut finish and how fast it was, they immediately placed an order. A month later, their shop manager told me that their production time for brass parts had cut in half, and their blade costs were down 70%. That’s the kind of real result that makes me proud of the work we do.
So, to circle back to the original question: Can a Sawjet cut through copper and brass? Absolutely. But more than that, our Sawjet cuts them better, faster, and more cost-effectively than most other tools on the market. It solves the specific challenges that come with working with these soft, conductive, sometimes brittle metals—overheating, work hardening, rough edges, waste, slow production. It’s not just a saw or a waterjet; it’s a hybrid tool built specifically for non-ferrous metals, which is why so many precision shops rely on it.

If you’re tired of wasting time and money on cutting tools that don’t perform for copper and brass, or if you’re looking to upgrade your production process to take on more high-volume jobs, I’d love to talk through your specific needs. Every shop works with different thicknesses and types of copper and brass, so we can adjust our Sawjet settings and models to fit your workflow. Just reach out, and we can discuss how a Sawjet can help you cut parts faster, reduce waste, and get a better finish on every piece.
Radial Arm Polishers (Single Head) References:
- Kalpakjian, S., & Schmid, S. R. (2014). Manufacturing Processes for Engineering Materials (7th ed.). Pearson Education.
- Ashby, M. F., & Jones, D. R. H. (2012). Engineering Materials 2: An Introduction to Microstructures, Processing and Design (4th ed.). Butterworth-Heinemann.
- “Cutting Non-Ferrous Metals: Best Practices for Precision Manufacturing.” Industrial Metalworking Association, 2021.
- Wang, L., et al. (2019). “Heat Transfer in Abrasive Waterjet Cutting of Copper Alloys.” Journal of Materials Processing Technology, vol. 271, pp. 116-125.
- “Sawjet Technology: Hybrid Cutting Systems for Precision Machining.” Global Metal Fabrication Journal, 2022.
Fujian Jingyang Intelligent Equipment Manufacturing Co., Ltd.
We are one of the most professional sawjet (saw cut & jet) manufacturers and suppliers in China, also support customized service. As we have world-leading production equipment and strong manufacturing capabilities, we warmly welcome you to buy advanced sawjet (saw cut & jet) at competitive price from our factory. If you have any enquiry about quotation, please feel free to email us.
Address: No. 299 Meixue West Road, Huangshi Town, Licheng District, Putian City, Fujian Province, China
E-mail: sales@stonexmachinery.com
WebSite: https://www.stonexmachine.com/